Explanatory Memorandum to COM(2000)172 - Accession of the EC to UNECE Regulation No 105 on the approval of vehicles intended for the carriage of dangerous goods with regard to their specific constructional features - Main contents
Please note
This page contains a limited version of this dossier in the EU Monitor.
| dossier | COM(2000)172 - Accession of the EC to UNECE Regulation No 105 on the approval of vehicles intended for the carriage of dangerous goods with ... |
|---|---|
| source | COM(2000)172  |
| date | 03-04-2000 |
Following Council Decision 97/836/EC of 27 November 1997, the EC became a contracting party to the United Nations Economic Commission for Europe's (UN/ECE's) Revised 1958 Agreement on 24 March 1998 and acceded to 78 regulations annexed to that Agreement.
Article 3 i of that Decision states, in particular, that the Community may decide to apply a Regulation to which it did not accede at the time of its accession to the Revised Agreement if the Council approves that Regulation by a qualified majority after receiving the assent of the EP.
Regulation No 105 on the approval of vehicles intended for the carriage of dangerous goods with regard to their specific constructional features is aimed, in particular, at removing technical barriers to trade in motor vehicles between the contracting parties while ensuring a high level of safety and environmental protection. Although that Regulation is not included in the list of regulations recognised by the EC that is contained in Annex II to Decision 97/836/EC, the representatives of the Member States have stated that it would now be useful if the EC were to examine the possibility of acceding thereto. It is also provided that the Regulation concerned will be incorporated into the approval system for motor vehicles and will thus supplement the laws in force within the Community.
It should be pointed out that the EC will take its decision regarding accession to that Regulation on the basis of the document that is available in the official languages of the UN/ECE (English, French and Russian). Therefore, only the French and English versions of Regulation No 105 have been appended.
In accordance with Article 4(5) of Decision 97/836/EC, Regulation No 105 will, however, be published in the Official Journal in all of the official languages of the Communities before it takes effect.
Contents
- 2. Content of the proposal for a Decision
- Sole Article
- For the Council
- GE.98-
- 1. Scope
- 2. Definitions
- 3. Application for approval
- 4. Approval
- 5. Technical provisions
- 6. Modification of the vehicle type and extension of approval
- 7. Conformity of production
- 8. Penalties for non-conformity of production
- 9. Production definitely discontinued
- 10. Names and addresses of technical services responsible for conducting approval tests, and of administrative departments
- 1. SCOPE
- 2. DEFINITIONS
- 3. APPLICATION FOR APPROVAL
- 4. APPROVAL
- 5. TECHNICAL PROVISIONS
- 5.1.1. ELECTRICAL EQUIPMENT
- 5.1.1.1. General provisions
- 5.1.1.2. Wiring
- 5.1.1.3. Battery master switch
- 5.1.1.5. Tachographs
- 5.1.1.6. Permanently energized installations
- 5.1.1.7.1. Wiring
- 5.1.1.7.2. Lighting
- 5.1.1.7.3. Electrical connections
- 5.1.1.7.4. Electrical lifting mechanism
- 5.1.2. Prevention of fire risks
- 5.1.2.2. Vehicle cab
- 5.1.2.3. Fuel tanks
- 5.1.2.4. Engine
- 5.1.2.5. Exhaust system
- 5.1.2.6. Vehicle endurance braking
- 5.1.2.7. Auxiliary heating device
- 5.1.3. Braking
- 5.1.4. Speed limitation
- 6. MODIFICATION OF THE VEHICLE TYPE AND EXTENSION OF APPROVAL
- 6.1.1. Consider that the modifications made are unlikely to have an appreciable adverse effect and that in any case the vehicle still complies with the requirements, or
- 7. CONFORMITY OF PRODUCTION
- 8. PENALTIES FOR NON-CONFORMITY OF PRODUCTION
- 9. PRODUCTION DEFINITELY DISCONTINUED
- Annex 1
- APPROVAL EXTENDED
- Annex 1
- Annex 2
- Model B
- NOTE DU SECRETARIAT GENERAL
- -pour avis : Service Juridique : avis favorable donné le 10 janvier 2000
The proposal for a decision is intended to enable the Community to accede to UN/ECE Regulation No 105 on the approval of vehicles intended for the carriage of dangerous goods with regard to their specific constructional features.
Proposal for a COUNCIL DECISION on the accession of the European Community to United Nations Economic Commission for Europe Regulation No 105 on the approval of vehicles intended for the carriage of dangerous goods with regard to their specific constructional features
THE COUNCIL OF THE EUROPEAN UNION,
Having regard to the Treaty establishing the European Community,
Having regard to Council Decision 97/836/EC of 27 November 1997 with a view to accession by the European Community to the Agreement of the United Nations Economic Commission for Europe concerning the adoption of uniform technical prescriptions for wheeled vehicles, equipment and parts which can be fitted to and/or be used on wheeled vehicles and the conditions for reciprocal recognition of approvals granted on the basis of these prescriptions (Revised 1958 Agreement) i, and in particular Article 3 i and the second indent of Article 4 i thereof,
Having regard to the proposal from the Commission i,
Having regard to the assent of the European Parliament i,
Whereas:
The standard requirements of United Nations Economic Commission for Europe Regulation No 105 on the approval of vehicles intended for the carriage of dangerous goods with regard to their specific constructional features are intended to remove technical barriers to trade in motor vehicles between the contracting parties in respect of specific constructional features of vehicles intended for the carriage of dangerous goods and to ensure a high level of safety and environmental protection.
Regulation No 105 has been notified to the Contracting Parties and has entered into force in respect of all the Contracting Parties who did not serve notice of their disagreement by the date or dates specified therein as a Regulation annexed to the Revised Agreement of 1958.
Regulation No 105 should be incorporated into the Community approval system for motor vehicles and thus be added to the legislation in force within the Community,
HAS DECIDED AS FOLLOWS:
The European Community accedes to United Nations Economic Commission for Europe Regulation No 105 on the approval of vehicles intended for the carriage of dangerous goods with regard to their specific constructional features i.
Done at Brussels,
The President
AGREEMENT CONCERNING THE ADOPTION OF UNIFORM TECHNICAL PRESCRIPTIONS FOR WHEELED VEHICLES, EQUIPMENT AND PARTS WHICH CAN BE FITTED AND/OR BE USED ON WHEELED VEHICLES AND THE CONDITIONS FOR RECIPROCAL RECOGNITION OF APPROVALS GRANTED ON THE BASIS OF THESE PRESCRIPTIONS [*]
[*] Former title of the Agreement:
(Revision 2, including the amendments entered into force on 16 October 1995)
Addendum 104: Regulation No. 105
Date of entry into force: 7 May 1998
UNIFORM PROVISIONS CONCERNING THE APPROVAL OF VEHICLES INTENDED FOR THE CARRIAGE OF DANGEROUS GOODS WITH REGARD TO THEIR SPECIFIC CONSTRUCTIONAL FEATURES
UNITED NATIONS
Agreement Concerning the Adoption of Uniform Conditions of Approval and Reciprocal Recognition of Approval for Motor Vehicle Equipment and Parts, done at Geneva on 20 March 1958.
Regulation No. 105
UNIFORM PROVISIONS CONCERNING THE APPROVAL OF VEHICLES
INTENDED FOR THE CARRIAGE OF DANGEROUS GOODS
WITH REGARD TO THEIR SPECIFIC CONSTRUCTIONAL FEATURES
CONTENTS
REGULATION
10. Names and addresses of technical services responsible for conducting approval tests, and of administrative departments
ANNEXES
Annex 1 - Communication concerning the approval or extension or refusal or withdrawal of approval or production definitely discontinued of a vehicle type with regard to specific constructional features for the transport of dangerous goods
Annex 2 - Arrangements of approval marks
The provisions of this Regulation apply to the construction of base vehicles of motor vehicles of category N and their trailers of categories O2, O3 and O4 which are subject to marginal 10 282 or 11 282 of annex B of the European Agreement concerning the International Carriage of Dangerous Goods by Road (ADR), as amended.
For the purpose of this Regulation:
2.1. 'Base vehicle' (hereinafter referred to as 'vehicle') means a chassis-cab vehicle, a tractor for semi-trailer, a trailer-chassis or a trailer with a self-supporting body intended for the transport of dangerous goods;
2.2. 'Vehicle type' means vehicles which do not differ essentially with regard to the constructional features specified in this Regulation.
3.1. The application for approval of a vehicle type with regard to its specific constructional features shall be submitted by the vehicle manufacturer or by his duly accredited representative.
3.2. The application for approval shall be accompanied by the undermentioned documents in triplicate and by the following particulars:
3.2.1. A detailed description of the vehicle type with respect to its relevant structure, engine (compression-ignition, positive-ignition), dimensions, configuration and constituent materials;
3.2.2. Vehicle designation, according to marginal 220 301 i of the ADR (EX/II, EX/III, AT, FL, OX);
3.2.3. Drawings of the vehicle;
3.2.4. The maximum technical mass (kg) of the complete vehicle.
3.3. A vehicle representative of the type to be approved shall be submitted to the technical service responsible for conducting the approval tests.
4.1. If the vehicle submitted for approval pursuant to this Regulation meets the provisions of paragraph 5 below, approval of that vehicle type shall be granted.
4.2. An approval number shall be assigned to each type approved. Its first two digits (00 for the Regulation in its present form) shall indicate the series of amendment incorporating the most recent major technical amendments made to the provisions at the time of issue of the approval. The same Contracting Party may not assign the same number to another vehicle type within the meaning of
paragraph 2.2. above.
4.3. Notice of approval or of extension of approval of a vehicle type pursuant to this Regulation shall be communicated to the Contracting Parties by means of a form conforming to the model reproduced in annex 1 to this Regulation.
4.4. There shall be affixed, conspicuously and in a readily accessible place specified on the approval form, to every vehicle conforming to a vehicle type approved under this Regulation an international approval mark consisting of:
4.4.1. A circle surrounding the letter 'E' followed by the distinguishing number of the country which has granted approval.[1]
4.4.2. The number of this Regulation, followed by the letter 'R', a dash and the approval number to the right of the circle prescribed in paragraph 4.4.1., and
4.4.3. An additional symbol separated from the approval number and consisting of the symbol identifying the vehicle designation in accordance with marginal 220 301 i of the ADR.
4.5. If the vehicle conforms to a vehicle type approved under one or more other Regulations annexed to this Agreement, in the country which has granted approval under this Regulation, the symbol prescribed in paragraph 4.4.1. need not be repeated; in this case the Regulation and approval numbers and the additional symbols of all the Regulations under which approval has been granted in the country which has granted approval under this Regulation shall be placed in vertical columns to the right of the symbol prescribed in paragraph 4.4.1.
4.6. The approval mark shall be clearly legible and be indelible.
4.7. The approval mark shall be placed close to or on the vehicle data plate affixed by the manufacturer.
4.8. Annex 2 to this Regulation gives an example of the approval mark.
5.1. Vehicles shall, depending on the vehicle designation, comply with the provisions below as assigned in the table overleaf.
The electrical installation as a whole shall meet the following provisions, in accordance with the table of paragraph 5.1.
5.1.1.2.1. The size of conductors shall be large enough to avoid overheating.
Conductors shall be adequately insulated. All circuits shall be protected by fuses or automatic circuit breakers, except for the following:
- from the battery to cold start and stopping systems of the engine
- from the battery to the alternator
- from the alternator to the fuse or circuit breaker box
- from the battery to the starter motor
- from the battery to the power control housing of the endurance braking system, if this system is electrical or electromagnetic
- from the battery to the electrical lifting mechanism for lifting the bogie axle
The above unprotected circuits shall be as short as possible.
>TABLE POSITION>
5.1.1.2.2. Cables shall be securely fastened and positioned in such a way that the conductors are adequately protected against mechanical and thermal stresses.
5.1.1.3.1. A switch for breaking the electrical circuits shall be placed as close to the battery as possible.
5.1.1.3.2. Direct or indirect control devices shall be installed, one in the driver's cab and a second on the outside of the vehicle. They shall be readily accessible and distinctively marked. The control device located in the driver's cab shall be within immediate reach of the driver seated in the driver's seat. It shall be protected against inadvertent operation by either adding a protective cover, or by using a dual movement control device or by other suitable means.
5.1.1.3.3. It shall be possible to open the switch while the engine is running, without causing any dangerous excess voltage. Operation of the switch shall not constitute a fire hazard in an explosive atmosphere; this can be ensured by using a switch having a casing with protection degree IP65 in accordance with IEC Standard 529.
5.1.1.3.4. The cable connections on the battery master switch shall have a protection degree IP54. However, this does not apply if these connections are contained in a housing which may be the battery box. In this case it is sufficient to insulate the connections against short circuits, for example with a rubber cap.
5.1.1.4. Batteries The battery terminals shall be electrically insulated or covered by the insulating battery box cover. If the batteries are not located under the engine bonnet, they shall be fitted in a vented box.
The electrical supply to the tachograph shall be provided via a safety barrier connected directly to the battery. The tachograph and the safety barrier shall meet the requirements for associated electrical equipment according to European Standard EN 50 020.
Those parts of the electrical installation, other than the tachograph, which remain energized when the battery master-switch is open, shall be suitable for use in a hazardous area and shall meet the appropriate requirements of European Standard EN 50 014 and one of European Standards EN 50 015 to 50 020 or EN 50 028. The requirements for the relevant gas group according to the
product being carried shall be met.
5.1.1.7. Provisions concerning that part of the electrical installation situated to the rear of the driver's cab The whole installation shall be so designed, constructed and protected such that it cannot provoke any ignition or short-circuit under normal conditions of vehicle use and that these risks can be minimized in the event of an impact or deformation. In particular:
The wiring located behind the driver's cab shall be protected against impact, abrasion and chafing during normal vehicle operation. Examples of appropriate protection are given in the figures 1, 2, 3 and 4 overleaf. However, the sensor cables of anti-lock braking devices do not need additional protection.
Lamp bulbs with a screw cap shall not be used.
Electrical connections between motor vehicles and trailers shall have a protection degree IP54 in accordance with IEC standard 529 and be designed to prevent accidental disconnection. Examples of appropriate connections are given in ISO 12 098:1994 and ISO 7638:1985.
The electrical equipment of the mechanism for lifting a bogie axle shall be installed outside the chassis frame in a sealed housing.
5.1.2.1. The following technical provisions shall apply in accordance with the table of paragraph 5.1.
5.1.2.2.1. Only material not readily flammable shall be used in the construction of the driver's cab. This provision will be deemed to be met if, in accordance with the procedure specified in ISO standard 3795:1989, samples of the following cab components have a burn rate not exceeding 100 mm/min : seat cushions, seat backs, safety belts, head lining, opening roofs, arm rests, all trim panels including door, front, rear and side panels, compartment shelves, head restraints, floor coverings, sun visors, curtains, shades, wheel housing covers, engine compartment covers, mattress covers and any other interior materials, including padding and crash-deployed elements, that are designed to absorb energy on contact by occupants in the event of a crash.
5.1.2.2.2. Unless the driver's cab is made of not readily flammable materials, a shield made of metal or other suitable material of the same width as the tank shall be fitted at the back of the cab. Any windows in the back of the cab or in the shield shall be hermetically closed and made of fire resistant safety glass with fire resistant frames. Furthermore, there shall be a clear space of not less than 15 cm between the tank and the cab or the shield.
The fuel tanks for supplying the engine of the vehicle shall meet the following requirements:
5.1.2.3.1. The fuel tanks shall be so placed as to be protected as far as possible against any collision;
5.1.2.3.2. In the event of any leakage, the fuel shall drain to the ground without coming into contact with hot parts of the vehicle or the load;
5.1.2.3.3. Fuel tanks containing petrol shall be equipped with an effective flame trap at the filler opening or with a closure with which the opening can be kept hermetically sealed.
The engine propelling the vehicle shall be so equipped and situated to avoid any danger to the load through heating or ignition. In vehicles designated EX/II and EX/III the engine shall be placed forward of the front wall of the body: it may nevertheless be placed under the body, provided this is done in such a way as to avoid any heating, even localized, of the load.
The exhaust system as well as the exhaust pipes shall be so directed or protected to avoid any danger to the load through heating or ignition. Parts of the exhaust system situated directly below the fuel tank (diesel) shall have a clearance of at least 100 mm or be protected by a thermal shield. In vehicles designated EX/II and EX/III the exhaust system shall be placed forward of the front wall of the body or separated from the load-carrying part of the vehicle by a fire-resistant and heat-insulating screen. In this case the exhaust pipe outlet shall be directed outwards from the vehicle.
Vehicles equipped with endurance braking systems emitting high temperatures placed behind the rear wall of the driver's cab shall be equipped with a thermal shield securely fixed and located between this system and the tank or load so as to avoid any heating, even local, of the tank shell or the load.
In addition, the thermal shield shall protect the braking system against any outflow or leakage, even accidental, of the load. For instance, a protection including a twin-shell shield shall be considered satisfactory.
Auxiliary heating for the cab shall be sufficiently secure from the standpoint of fire prevention and shall be placed forward of the protective wall (rear wall of the cab). The heating appliance shall be placed as far forward and as high as possible (at least 80 cm above floor level) and shall be fitted with devices preventing any object from being brought into contact with the hot surfaces of the appliance or its exhaust pipe. Only appliances with a means of rapidly restarting the combustion air ventilator (max. 20 s) may be
used.
5.1.3.1. Vehicles subject to the requirements of marginal 10 221 of ADR shall fulfil all relevant requirements of Regulation No. 13 including those of annex 5.
5.1.3.2. Other vehicles shall fulfil all relevant requirements of Regulation No. 13 except those of annex 5.
Motor vehicles (rigid vehicles and tractors for semi-trailers) with a maximum mass exceeding 12 tonnes, shall be equipped with a speed limitation device according to the provisions of ECE Regulation No. 89. The limitation speed V as defined in paragraph 2.1.1. of ECE Regulation No. 89 shall not exceed 85 km/h.
6.1. Every modification of the vehicle type shall be notified to the administrative department which approved the vehicle type. The department may then either:
6.1.1. Consider that the modifications made are unlikely to have an appreciable adverse effect and that in any case the vehicle still complies with the requirements, or
6.1.2. Require a further test report from the technical service responsible for conducting the tests.
6.2. Confirmation or refusal of approval, specifying the alteration, shall be communicated by the procedure specified in paragraph 4.3. to the Contracting Parties.
6.3. The competent authority issuing an extension of approval shall assign a series number to each communication form drawn up for such an extension and inform thereof the other Parties by means of a communication form conforming to the model in annex 1 to this Regulation.
The conformity of production procedures shall comply with those set out in the Agreement, Appendix 2 (E/ECE/324-E/ECE/TRANS/505/Rev.2), with the following requirements:
7.1. Vehicles approved to this Regulation shall be so manufactured as to conform to the type approved by meeting the requirements set forth in paragraph 5 above.
7.2. The competent authority which has granted type-approval may at any time verify the conformity control methods applicable to each production facility. The normal frequency of these verifications shall be once per two years.
8.1. The approval granted in respect of a vehicle type pursuant to this Regulation may be withdrawn if the requirement laid down in paragraph 7. above is not complied with.
8.2. If a Contracting Party to the Agreement applying this Regulation withdraws an approval it has previously granted, it shall forthwith notify the other Contracting Parties applying this Regulation, by means of a communication form conforming to the model in annex 1 to this Regulation.
If the holder of the approval completely ceases to manufacture a type of vehicle under this Regulation, he shall so inform the authority which granted the approval. Upon receiving the relevant communication, that authority shall inform thereof the other Parties to the 1958 Agreement applying this Regulation by means of a communication form conforming to the model in annex 1 to this Regulation.
10. NAMES AND ADDRESSES OF TECHNICAL SERVICES CONDUCTING APPROVAL TESTS, AND ADMINISTRATIVE DEPARTMENTS.
The Contracting Parties to the Agreement applying this Regulation shall communicate to the secretariat of the United Nations the names and addresses of the technical services responsible for conducting approval tests and of the administrative departments which grant approval and to which forms certifying approval or extension or refusal or withdrawal of approval, issued in other
countries, are to be sent.
COMMUNICATION
(maximum format: A4 (210 x 297 mm))
issued by: Name of administration:
.......................
.......................
.......................
concerning: i APPROVAL GRANTED
APPROVAL REFUSED
APPROVAL WITHDRAWN
PRODUCTION DEFINITELY DISCONTINUED
of a vehicle type with regard to specific constructional features for the
transport of dangerous goods.
Approval No.: ..... Extension No.: .....
1. Trade name or mark of the vehicle ..................
2. Vehicle category: N1, N2, N3, O2, O3, or O4: ............
(chassis-cab, tractor for semi-trailer, trailer-chassis, trailer with a self-supporting body i).
3. Vehicle type: ............................
4. Vehicle designation (EX/II, EX/III, FL, OX, AT): ...........
5. Manufacturer's name and address: ...................
6. If applicable, name and address of manufacturer's representative: .. ...................................
7. Mass of the vehicle:
7.1. Technical maximum mass of complete vehicle: .............
8. Specific equipment of the vehicle:
8.1. The vehicle is/is not i equipped with specific electrical devices. Summary description .........................
8.2. The vehicle is/is not i equipped with devices for the prevention of fire risks.
Summary description .........................
8.3. In the case of a motor vehicle:
8.3.1. Type of engine: positive-ignition, compression-ignition i
9. Vehicle submitted for approval on: ..................
10. Technical service responsible for carrying out approval inspections: ...................................
11. Date of report issued by that service: ................
12. Number of report issued by that service: ...............
13. Approval granted/refused/extended/withdrawn i ............
14. Position of approval mark on the vehicle: ..............
15. Place: ................................
16. Date: ................................
17. Signature: .............................
1/ Distinguishing number of the country which has granted/extended/refused or withdrawn approval (see footnote 1/ to paragraph 4.4.1.).
ARRANGEMENTS OF APPROVAL MARKS
Model A
(see paragraph 4.4. of this Regulation)
(FIGURE - OFFSET)
a = 8 mm min.
The above approval mark affixed to a vehicle shows that the vehicle type concerned, intended for the transport of dangerous goods, has been approved in the Netherlands (E4), pursuant to Regulation No. 105, under the approval number 002492 and designated EX/II (according to marginal 220 301 i of the ADR). The first two digits of the approval number indicate that the approval was granted in accordance with the requirements of Regulation No. 105 in its original form.
(see paragraph 4.5. of this Regulation)
(FIGURE - OFFSET)
a = 8 mm min.
The above approval mark affixed to a vehicle shows that the vehicle type concerned has been approved in the Netherlands (E4) pursuant to Regulations Nos. 105 and 13 i. The first two digits of the approval numbers indicate that, at the dates when respective approvals were granted, Regulation No. 105 was in its original form, while Regulation No. 13 already included the 09 series of amendments.
PREPARATION DU DOCUMENT
-Direction générale responsable : ENTREPRISES
-Services associés :
-Langue originale : FR
-Référence document de travail : III/5690/99